Silver Dawn Chassis
SILVER DAWN
The chassis number for these models is composed of an initial fixed letter 'S', followed by a second letter that can go up to V. The third letter determines the series of the model. It ends with a number that can go from 1 to 160.
An 'L' in front of the whole chassis number means the model is long wheelbase
Usually the chassis number for these models can be found on the firewall.
Release dates | Chassis number | Modification | Modification introduced at |
Apr. 49 to Jun.50 | SBA2 to SBA138 | C&A cylinder head gasket | SBA16 |
Jun. 50 to Mar. 51 | SCA1 to SCA63 | 3/8 in. dia. rear axle bolts | SBA16 |
Modified S.S. tube socket (LSBA76) | SBA16 | ||
Modified X.S. tube socket (LSBA106) | SBA16 | ||
One piece shackle bracket | SBA16 | ||
Longer gear change lever |
SBA26 |
||
Modified throttle return spring | LSBA28 | ||
Apr. 49 to Jun. 50 | SBA2 to SW138 | Felt bush in steering col. gear change | LSBA44 |
Jun. 50 to Mar. 51 | SCA1 to SCA63 | Modified R.S.D. plates | LSBA46 |
(continued) | Revesed linkage & rubber grommet in steering column gear change | LSBA76 | |
Rear shackle Bijur pipes revised | SBA140 | ||
Modified carburetter | SBA128 (LSBA131) | ||
Modified speedo and drive | SBA130 | ||
2nd mod. to rear spring plate | LSBA138 | ||
Revised steering geometry | SCA1 | ||
Anti-rumble front brakes | SCA1 | ||
Thicker lipped brake drums | SCA1 | ||
Modified rear No. plate box | SCA1 | ||
Keyhole sockets on gear control | LSCA11 | ||
Reduced speed fan | LSCA9 | ||
One piece rear brake equ-lever | LSCA17 | ||
Aluminium cam wheel | LSCA23 | ||
3 bush rear brake equ-support | SCA27 (LSCA23) | ||
Modified starter solenoid switch | SCA27 | ||
Low rate oil feed to clutch | SCA29 | ||
Lower bush R.S.D. link deleted | SCA29 | ||
11” clutch (light type) SCA-27 | LSCA41 | ||
Modified clutch spigot bearing | SCA45 | ||
Closer fitting 2nd & 3rd speed bushes | LSCA51 | ||
Longer bosses on R.S.D plates | LSCA51 | ||
Triple Pass de-mister inter. scheme | LSCA53 | ||
Nov. 50 to Aug. 51 | SDB2 to SDB140 | Thicker rear SD. plates | LSDB2 |
Triple pass R.H de-mister (final) | LSDB6 | ||
Modified water pump gland ring | SDB12 | ||
New type ignition condenser | SDB40 | ||
Side scuttle ventilators | SDB44 | ||
Steel oil caps in crankshaft | LSDB58 | ||
Heavy type clutch | SDB76 | ||
JuI. 51 to Jul. 52 | SFC2 to SFC160 | 3/8 in. bore engine | LSFC2 |
Thickened crankshaft webs | LSFC2 | ||
Full flow oil filter | LSFC2 | ||
Insulated dynamo | SFC64 | ||
Increased front damping | SFC92 | ||
Twin condensers | SFC94 | ||
120° opening ventilator windows | SFC94 | ||
Rear window de-mister | SFC94 | ||
3-position heater and de-mister switches | LSFC102 | ||
Single choke Zenith carburetter | LSFC102 | ||
Short dwell detent on 1st gear selector | SFC122 | ||
Mar. 52 to Sep. 52 | SHD2 to SHD60 | Repositioned oil gauge connection on crankcase | LSHD6 |
Stiffened clutch casing | SHD18 | ||
Reversion to old type front wheel studs | LSHD56 | ||
Mark II headlamps | LSHD56 | ||
Jul. 52 to Jan. 53 | SKE2 to SKE50 | Revised luggage boot | SKE2 |
Nov. 52 to May. 53 | SLE1 to SLE51 | Revised attitude rear springs | SKE2 |
Redesigned rear shock damper linkage | SKE2 | ||
Two speed windscreen wiper | SKE2 | ||
Hot and cold de-mister | SKE2 | ||
Reduced friction on steering connections | SKE2 | ||
Needle rollers on clutch release fevers | SKE2 | ||
Caster angle wedges | SKE2 | ||
Deletion of hand throttle control | SKE2 | ||
Pop-out cigar lighter | SKE2 | ||
Separately housed main fuse | SKE2 | ||
Solid pins and shield on servo | SKE2 | ||
Corrugated bottom water hose connection | SKE10 | ||
Taper roller bearings on rear axle pinion (except 12/41 axles) | SLE11 | ||
3 1/2 seconds slow leak on front shock dampers | SLE31 | ||
Dec. 52 to Sep. 53 | SMF2 to SMF76 | Taper roller bearings on rear axle pinion (12 x41 axles) | SMF42 |
Jul. 53 to Feb. 54 | SNF1 to SNF125 | Parco lubrized tappets | SME50 |
6.75 compression ratio cylinder head | SMF62 | ||
B.VI camshaft (LH cars only) | SMF66 | ||
Deletion of non-opposed springs in side steering tube | SMF70 | ||
All welded frame | SNF1 | ||
Cable operated hot and cold de-mIster and underseat heater | SNF1 | ||
Hard clay gasket | SNF15 | ||
Deletion of reduced friction modifications on steering connections | SNF27 | ||
Improved type underseat tool tray | SNF109 | ||
lntroduction of B.VI type gearbox tie rod | SNF113 | ||
Feb. 54 to Aug. 54 | SOG2 to SOG100 | Fitting of inertia ring on flywheel | SOG86 |
Mar. 54 to Sep.54 | SPG1 to SPG101 | Dynamo type mounting strapon starter motor | SPG11 (RH) |
Compensator pipe between front and rear servo | SPG37 | ||
Thicker third motion shaft thrust washer | SPG37 | ||
Feb. 54 to Aug. 54 | SRH2 to SRH100 | Twin exhaust system | SRH2 |
Aug. 54 to Ott. 54 | STH1 to STH101 | 12/41 rear axle (all cars) | SRH2 |
Strengthened jaws on front brake operating links | SRH4 | ||
Feb.54 to Aug. 54 | SRH2 to SRH100 | Elimination of chromium-plated servo pressure plate | SRH50 |
Aug. 54 to Ott. 54 | STH1 to STH101 | Dynamo type mounting strap on starter motor | SRH72 (LH) |
(continued) | Aluminium flywheel housing | SRH72 | |
Long stroke starter pinion | STH57 | ||
Ott. 54 to Jan. 55 | SUJ2 to SUJ130 | Bentley continental type de-misting | SUJ14 |
Nov. 54 to Apr. 55 | SVJ1 to SVJ133 | 2nd speed start | SUJ50 |
Ferodo washer and drain slots in crankshaft vibration damper | SVJ101 |